Winpossee Dvr Default Password đź’Ż Plus

For Winpossee DVRs, the default admin password is typically blank (no password) or one of several common factory defaults used by similar DVR manufacturers. Common Default Credentials Username: admin Default Passwords to Try: (Blank) — Leave the password field empty. 123456 admin 000000 or 111111 12345 How to Reset a Forgotten Password

If the default credentials do not work, you may need to reset the device to factory settings:

Internal Battery Method: On some Winpossee/XMEye-based boards, you can open the DVR case and remove the small CMOS silver battery for approximately 30 seconds. This often resets the system clock and clears the admin password back to the blank default.

Physical Reset Button: Look for a small button on the back or on the internal motherboard. Press and hold it for 10–30 seconds while the unit is powering on. winpossee dvr default password

QR Code Reset: Some modern Winpossee models allow you to generate a reset QR code from the local login screen, which can be scanned using the manufacturer's mobile app (often XMEye or Wecam Pro) to receive a temporary recovery code.

Master Password Generators: If you know the date shown on the DVR's screen, certain "super password" generators for H.264 DVRs can create a one-day master code to unlock the device.

6. How to Verify If Your Winpossee DVR Uses a Default Password

  1. Locate IP of DVR (check router DHCP list or use Winpossee app → Device Info).
  2. Open browser → http://<DVR-IP>
  3. Login with admin and try: (blank), 123456, 888888, 666666.
  4. If success → your system is critically vulnerable.

Alternatively, use curl:

curl --digest -u admin: http://<DVR-IP>/cgi-bin/eventManager.cgi?action=getEventIndex

If you receive a JSON/XML response without password, the device is open.

Q2: My Winpossee DVR is rebranded (e.g., “Zosi,” “Amcrest”). Does default password differ?

Yes, but rarely. Many white-label DVRs use the same firmware. Try admin/12345 first. If that fails, search for the specific brand’s default (e.g., Zosi often uses admin/000000).

Q1: Will resetting the password delete my recorded videos?

No. Password reset via the backdoor code or physical button clears only the login credentials. Hard drive footage remains intact. For Winpossee DVRs , the default admin password

3. Known Default Credentials by Winpossee Model/App

Based on real-world device analysis and security forums:

| Model / App | Username | Default Password | |-----------------------|----------|------------------| | Winpossee 4/8/16CH DVR| admin | (blank) | | Winpossee NVR | admin | 123456 | | Winpossee CamHi-based | admin | 888888 | | Winpossee IPC (IP Cam) | admin | 111111 | | Winpossee (older) | admin | 666666 |

Important: The associated mobile apps (e.g., Winpossee, CamHi, Yoosee, Tosee) often sync credentials but do not force a password change. Locate IP of DVR (check router DHCP list

Method 2: Physical Reset Button (Hardware Reset)

If the backdoor code fails or your model does not have a “Forgot Password” option, use the physical reset:

  1. Power off the DVR.
  2. Open the case (you may void the warranty, but this is often necessary).
  3. Locate a small tactile button or two-pin jumper labeled RST, RESET, SW1, or CLEAR.
  4. Use a plastic spudger or paperclip to press and hold the button.
  5. While holding the reset button, power the DVR back on.
  6. Continue holding for 10–15 seconds, then release.
  7. The DVR will boot with factory settings: Username admin / Password 12345.

No physical button? Look for two exposed pins. Short them with a screwdriver for 5 seconds while powering on.