Onkyo Rc-799m Remote Manual

The Onkyo RC-799M Remote Manual: A Complete Guide to Mastering Your Home Theater

Published: October 3, 2023 | Category: Home Audio & Troubleshooting

If you are reading this, you have likely just unearthed a classic piece of AV history—or you are currently sitting on your couch, pressing buttons on a sleek, black wand that refuses to turn up the volume on your receiver.

Welcome to the definitive guide for the Onkyo RC-799M remote control.

Whether you lost the original paper manual, bought a used receiver without the remote, or simply want to program your universal remote to replace this one, you have come to the right place.

Quick Reference — Common Button Shortcuts

• Power toggle: POWER
• Mute: MUTE
• Volume up/down: VOLUME + / -
• Cycle inputs: INPUT / SELECT
• Open receiver menu: MENU / HOME
• Navigate menus: Arrow keys + ENTER
• Switch zones: ZONE / ZONE2

If you want, I can produce:

• A colorful printable PDF layout of this handbook,
• A one‑page quick reference card,
• Or a labelled button diagram for the RC-799M.

Which would you like?

Onkyo RC-799M Go to product viewer dialog for this item. is a primary remote control for various Onkyo and Integra A/V receivers, known for its ability to manage multi-zone functions and basic control of external devices like TVs and DVD players. Essential Setup and Programming onkyo rc-799m remote manual

While many replacement versions are "ready to use" for Onkyo receivers immediately upon inserting batteries, original or high-end versions can be programmed to control other home theater components. Programming for a TV:

Hold down the TV button and the Display button simultaneously for approximately 3 seconds until the remote indicator light stays lit.

Within 30 seconds, enter the 5-digit TV code using the number keys. For example, a common code for Sharp TVs is 10818.

If successful, the indicator light will flash twice. If it flashes once slowly, the programming failed. Assigning Codes to Other Devices:

Hold the desired Remote Mode button (e.g., BD/DVD, CBL/SAT) and the Display button for 3 seconds.

Enter the corresponding 5-digit code for your device brand from the official Onkyo Remote Code List. Test the device by pressing the Power button. Key Button Functions The Onkyo RC-799M Remote Manual: A Complete Guide

features a layout optimized for receiver navigation and media playback. Description Zone 2 Control

The ZONE 2 and OFF buttons allow you to manage audio in a second room independently. Setup Menu

Use the Q/Setup button to access advanced on-screen settings on your TV. Navigation

The central Cursor (arrows) and Enter buttons are used for menu navigation and radio tuning. Dimmer

Adjusts the brightness of the receiver's front panel display in three steps. Compatibility List

is compatible with a wide range of Onkyo home theater systems and receivers, including: Power toggle: POWER Mute: MUTE Volume up/down: VOLUME

HT-S Series: HT-S3300, HT-S3400, HT-S3500, HT-S5100, HT-S5400, HT-S5500 HT-R Series: HT-R391, HT-R548, HT-R558, HT-R590, HT-R591

TX-SR Series: TX-SR309, TX-SR313, TX-SR506, TX-SR576, TX-SR607, TX-SR608 TX-NR Series: TX-NR414, TX-NR515 Troubleshooting Common Issues Anderichttps://www.anderic.com

Step 2: Pairing (There is no pairing)

Good news: This remote does not use Bluetooth or RF. It uses IR. As long as your Onkyo receiver has a clear line of sight to the remote, it will work automatically. There is no "sync" button.

Key Physical Features

• Dimensions: 8.5 x 2.1 x 1.2 inches
• Battery Type: 4 x AAA (Alkaline recommended; do not use rechargeable NiMH as the lower voltage can cause erratic behavior)
• Signal Type: Infrared (Line of sight required)
• Backlight: Yes (Activated by pressing the "Light" button at the top right)

Programming & Pairing

If your RC-799M is a learning or system remote that requires pairing:

1. Power on the Onkyo receiver.
2. If a dedicated pairing sequence exists, press and hold SETUP until the indicator LED blinks.
3. Use the remote’s on‑screen or printed code list to enter the code for your specific Onkyo model (if required).
4. Test POWER and VOLUME. If successful, press ENTER or SETUP to store.

If the remote supports discrete codes or device mode switching, try the following:

• Press the device mode key (e.g., AMP, TUNER, TV), then press and hold POWER until the device responds.
• If the device responds, press ENTER to lock the code.

If the remote is a learning remote:

• Place the original device remote and RC-799M head‑to‑head.
• Enter learning mode (press SETUP, then the learning command).
• Press the source button on the RC-799M, then the corresponding button on the original remote to copy the IR signal.
• Repeat for each button to be learned, then exit learning mode.

Quick Start — Setup (2 minutes)

1. Insert two AAA batteries into the battery compartment, matching polarity.
2. Point the remote at the receiver and press [POWER] to turn it on.
3. If the remote doesn’t control the receiver immediately, follow the pairing/programming steps below.

Problem 1: The LED blinks, but the device doesn’t respond.

• Cause: Weak batteries or line-of-sight blocked.
• Fix: Replace with fresh alkaline AA batteries. Clean the IR emitter (the purple/black plastic at the top) with a dry microfiber cloth. Ensure you are within 15 feet.

How to Program a Macro (e.g., "Watch TV"):

1. Press and hold Setup until two flashes.
2. Press the Macro button (located near the bottom, labeled "MACRO").
3. Press the button you want to assign the macro to (e.g., 1). LED flashes once.
4. Now, press the sequence of original button presses in order:
   • Press TV Device button → Power
   • Press RECEIVER Device button → Power
   • Press CBL/SAT Device button → Power
5. Press the Macro button again to save. LED flashes twice.

Now, pressing 1 will execute all three power commands with a 0.5-second delay between each.