Intronics Digital Room Thermostat User Guide 〈FULL〉

Intronics digital room thermostat line, produced by Intronics Co., Ltd. , includes several popular models like the DT-03 Plus Digital Room Thermostat II

. These units are typically used for fan coil systems, mini-split ACs, or chilled water systems. Sangchai Group Basic Operation

For most digital models (e.g., DT-03, DT-08, and Series II), the core controls remain consistent: Power On/Off : Press the button to toggle the unit. Most models feature an Auto Restart

function that resumes previous settings after a power failure. Adjusting Temperature

(or Up/Down arrow) buttons. The display usually shows the new target temperature for about 5 seconds before reverting to the current room temperature. : The setting range is typically 15–30°C (58–88°F). : Press the button to cycle through

speeds. In "Auto," the thermostat adjusts speed based on the difference between actual and target room temperature. Mode Selection : Press the button to cycle through available operations: Sangchai Group Advanced Features Turbo Function : Available on models like the , this allows for rapid cooling. Econo/Sleep Mode

: These energy-saving modes gradually adjust the temperature over several hours to improve comfort while you sleep and reduce power usage. button to set an automatic "On" or "Off" time. Compressor Protection : Most units have a built-in 3-minute time delay

to prevent the compressor from cycling too quickly, which protects the system from damage. Sangchai Group System Indicators Status Dot

: A lit dot on the digital display (often after the second digit) usually indicates that the compressor is currently active. Error Alarms

: If the display dots blink or show an error code, it typically indicates a sensor error (open or short circuit). Sangchai Group Installation & Maintenance : Models like the

often use a 2-wire cable between the main power unit and the wall-mounted display.

: Use a soft, dry cloth to clean the touch panel. Avoid liquid cleaners that could seep into the electronics.

Intronics Digital Room Thermostat User Guide The Intronics series of digital room thermostats, including the popular , , and Series II LED/LCD

models, are designed for high-precision HVAC control in residential and commercial settings. This guide provides the necessary steps for installation, operation, and advanced configuration to ensure your system runs efficiently. 1. Key Features and Models

Intronics thermostats typically feature Proportional + Integral (P+I) control, which minimizes temperature fluctuations compared to standard on/off controllers. PI02 Model : 24 VAC floating digital thermostat. PI04 Model : 24 VAC/VDC modulating digital thermostat. Series II LED/LCD

: Versatile units for fan coil systems, available in 24V, 120V, and 220V versions.

Standard Features: Backlit display, 3 fan speeds, compressor time delay, and non-volatile memory (EEPROM) that saves settings during power loss. 2. Installation Guide

Warning: Only trained technicians should perform the installation to avoid damaging the heating or cooling system. Mounting Location

For accurate readings, mount the unit approximately 5 feet (1.5m) above the floor. Avoid placing it: In direct sunlight or near heat-producing appliances. Near drafts, doors, or windows. On exterior walls. Wiring and Mounting

Disconnect Power: Turn off the main breaker to the HVAC equipment before starting.

Separate the Backplate: Use a flat-head screwdriver to unlock the snaps at the bottom of the thermostat and pull the backplate away.

Connect Wires: Use 18-22 gauge wire. Follow the terminal designations on the back of the unit. Ensure connections are firm.

Secure Unit: Screw the backplate to the wall using the provided anchors and snap the thermostat body into place. 3. Operating Instructions

Once installed, the basic operation of an Intronics thermostat is straightforward. Intronics digital room thermostat user guide

The Intronics digital room thermostat series, including popular models like the DT-08 and Digital Room Thermostat II, offers specialized control for HVAC systems like mini-splits, duct-type units, and chilled water systems. Core Controls & Functions

Most Intronics digital thermostats feature a capacitive touch panel with backlit buttons for easy operation:

Power On/Off: Use the dedicated power button to activate or shut down the air conditioning unit.

Temperature Setting: Use the Up and Down arrows to adjust your target temperature. Standard adjustable ranges are typically between 5°C and 35°C.

Fan Speed Control: Press the Fan button to cycle through Low, Medium, and High speeds. Selecting AUTO allows the thermostat to adjust fan speed based on the difference between current and set room temperatures.

Operation Modes: Select between Cool, Fan, or Heat modes (depending on your specific model version) using the Mode button. Advanced Comfort Features

Sleep Function: Pressing Sleep gradually raises the set temperature by 1°C after one hour in Cool mode (or reduces it in Heat mode) to save energy while you sleep.

Turbo & Econo: Use the Turbo function for rapid cooling or Econo for energy-saving operation.

Timer: You can set a delay of up to 15 or 24 hours (model dependent) to automatically turn the unit on or off in advance.

Sweep (Optional): If your unit supports it, the Sweep button toggles the oscillating motor for wider air distribution. Standard Installation Guide

Installation should be performed with the voltage supply switched off. Intronics digital room thermostat user guide

Master Your Comfort: The Intronics Digital Room Thermostat User Guide

If you've just installed an Intronics digital room thermostat, you're one step closer to a more efficient and comfortable home. Digital thermostats offer much more precision than old-school dial models, but they can be a bit intimidating at first glance.

Here is a straightforward guide to getting your Intronics unit up and running. 1. Understanding the Display

Most Intronics models feature a clear LCD screen. You’ll typically see two numbers: Current Temperature: The actual temperature currently detected in the room. Set Temperature: The "target" temperature you want the room to reach. Status Icons:

Look for a flame icon (heating is active) or a snowflake (cooling/frost protection is active). 2. Basic Temperature Adjustment Changing the heat is usually a two-button job. Increase/Decrease:

(or Up/Down arrow) buttons to adjust your target temperature. Confirmation:

On many models, the screen will flash for a few seconds after you set a new temperature. Once it stops flashing, the setting is saved. 3. Setting the Programs (Schedule)

To save the most money, you should program your thermostat to lower the heat when you're asleep or out of the house. Enter Program Mode: Press and hold the Select the Day:

Use the arrows to choose between Weekdays (1-5) and Weekends (6-7). Time Slots:

Most units allow for 4–6 "events" per day (e.g., Wake, Leave, Return, Sleep).

Set the start time for the first event, then the desired temperature. Repeat for all slots.

Press 'Set' or wait for the screen to return to the home display. 4. Advanced Modes Manual Overrun: intronics digital room thermostat user guide

If you're home early and want it warmer, simply press the [+] button. The thermostat will usually stay at this "manual" temperature until the next scheduled program starts. Holiday Mode:

Look for a suitcase icon. This lets you set a fixed, low temperature (like 10°C) for several days while you’re away to prevent pipes from freezing without wasting energy. Frost Protection:

Even when "off," many Intronics thermostats will automatically kick in if the temperature drops below 5°C to protect your home. 5. Quick Maintenance Tips Battery Low:

If you see a battery icon, swap them out immediately (usually 2x AA). If the batteries die completely, your boiler might stop receiving signals. Placement Matters:

Ensure your thermostat isn't behind a curtain, in direct sunlight, or near a drafty door, as this will trick the sensor and lead to uneven heating.

Experts suggest finding the lowest temperature you’re comfortable with—often around 18-21°C (64-70°F)—and leaving it there. Constantly cranking it up to "heat faster" doesn't actually speed up the boiler; it just wastes energy. or setting up a 7-day custom schedule General Room Thermostat information

The Intronics digital room thermostat series offers a reliable, straightforward HVAC control solution featuring a modern design with an intuitive LED/LCD interface, as detailed in user documentation. These mercury-free units support various system types and include, according to installation manuals, specialized modes such as Turbo cooling, Econo/Sleep settings, and non-volatile memory for maintaining settings. For the complete user guide and technical specifications, refer to the Sangchai Group product catalog cdn.prod.website-files.com Intronics digital room thermostat user guide

Intronics Digital Room Thermostat: The Ultimate User Guide An Intronics digital room thermostat is a reliable, straightforward tool designed to help you maintain the perfect balance between comfort and energy efficiency. Whether you’ve just installed a new unit or moved into a home with one already on the wall, understanding how to navigate its interface is key to a cozy home.

This guide covers everything from basic temperature adjustments to advanced programming and troubleshooting. 1. Getting Started: The Interface

Most Intronics digital models feature a clear LCD screen and a simple button layout. Before diving into settings, identify these core components:

The Display: Shows the current room temperature, the setpoint (desired temperature), and the current mode (Heat/Cool/Auto).

Up/Down Arrows: Used to adjust the temperature and navigate menu options.

Set/Program Button: Enters the configuration menu for scheduling. Mode Switch: Toggles between Heating, Cooling, and Off. 2. Basic Operation How to Set the Temperature

The most common task is a manual override. To change the temperature immediately: Press the Up or Down arrow buttons once to wake the screen. Adjust to your desired temperature.

Wait five seconds; the thermostat will save the setting and begin triggering your HVAC system. Switching Modes

Ensure your thermostat is set to the correct season. Use the Mode button (or physical slider on some models) to select: Heat: To activate your furnace or boiler. Cool: To activate your air conditioning. Off: To shut down the system entirely. 3. Programming Your Schedule

Programming allows the thermostat to automatically lower the heat while you’re at work or asleep, saving you significant money on utility bills. Step-by-Step Programming:

Enter Program Mode: Press and hold the Set or Prog button until the clock begins to flash.

Set the Time: Use the arrows to set the current time and day. Press Set to confirm.

Choose the Period: Most Intronics units use a 5-2 day schedule (Weekdays vs. Weekends) or a 7-day schedule.

Set Wake Time/Temp: Adjust the time you wake up and the temperature you want. Press Set.

Set Leave/Return/Sleep: Repeat the process for when you leave the house, return home, and go to bed.

Exit: Once all periods are set, press Run or wait for the screen to return to the main display. 4. Advanced Features

Temporary Hold: If you adjust the temperature during a scheduled program, the thermostat will stay at that temperature until the next scheduled time block begins.

Permanent Hold: To maintain a temperature indefinitely (like when you go on vacation), press the Hold button after setting your temperature. Press Run Program to cancel.

Differential Settings: Some digital models allow you to set the "swing" or "deadband." This determines how many degrees the temperature must drop before the heat kicks back on, preventing your system from "short-cycling." 5. Maintenance and Battery Replacement

If your screen is blank or the "Low Bat" indicator appears, it is time to change the batteries. Gently pull the thermostat body away from the wall plate. Replace the batteries (usually 2 x AA or AAA alkalines).

Snap the unit back onto the wall. Your saved programs should remain intact for a few minutes while you swap batteries, but it’s always good to check. 6. Troubleshooting Common Issues

System won’t turn on: Check that the Mode is set to Heat or Cool and that the setpoint is higher (for heat) or lower (for cool) than the current room temperature.

Display is blank: Check the batteries and the circuit breaker in your electrical panel.

Delayed Start: Many Intronics models have a built-in 5-minute delay to protect the compressor. If your AC doesn’t kick on immediately, wait a few minutes. Conclusion

The Intronics Digital Room Thermostat is designed for "set it and forget it" convenience. By taking ten minutes to program your weekly schedule, you can enjoy a comfortable home environment while reducing your carbon footprint and monthly costs.

Intronics Digital Room Thermostat User Guide: A Comprehensive Report

Introduction

Intronics, a leading provider of innovative heating and cooling solutions, has developed a cutting-edge digital room thermostat designed to provide precise temperature control and energy efficiency. The Intronics Digital Room Thermostat is a user-friendly device that allows homeowners to effortlessly regulate their indoor climate. This report provides an in-depth guide on how to use and optimize the features of the Intronics Digital Room Thermostat.

Overview of the Thermostat

The Intronics Digital Room Thermostat is a sleek and modern device that boasts a range of advanced features. The thermostat is designed to be easy to use, with a clear and intuitive interface that allows users to set and adjust their desired temperature with ease. The device is compatible with most heating and cooling systems, making it a versatile solution for homeowners.

Key Features

The Intronics Digital Room Thermostat comes equipped with the following features:

Digital Display: A clear and easy-to-read LCD display shows the current temperature and setpoint.
Programmable Schedule: Users can set a schedule to adjust the temperature at different times of the day.
Temperature Control: The thermostat allows for precise temperature control, with a range of 32°F to 80°F (0°C to 27°C).
Energy Efficiency: The device is designed to optimize energy efficiency, helping homeowners reduce their energy bills.
Adaptive Recovery: The thermostat learns the heating and cooling system's response time to ensure that the desired temperature is reached at the set time.

Operating the Thermostat

Operating the Intronics Digital Room Thermostat is straightforward. Here's a step-by-step guide:

Setting the Temperature: Press the "SET" button to adjust the desired temperature. Use the "+" and "-" buttons to increase or decrease the temperature.
Programming the Schedule: Press the "SCHEDULE" button to set a custom schedule. Choose from a range of pre-set options or create a personalized schedule.
Changing the Mode: Press the "MODE" button to switch between heating, cooling, or auto modes.
Locking the Thermostat: Press the "LOCK" button to prevent unauthorized changes to the settings.

Tips and Tricks

To get the most out of the Intronics Digital Room Thermostat, follow these tips:

Set a realistic temperature: Avoid setting extreme temperatures, as this can lead to energy waste and decreased efficiency.
Use the schedule feature: Programming a schedule can help homeowners save energy and money.
Adjust the thermostat's sensitivity: The device's sensitivity can be adjusted to suit individual preferences.

Troubleshooting

If issues arise with the Intronics Digital Room Thermostat, refer to the troubleshooting guide:

Display issues: Check that the device is properly powered and that the display is clean.
Temperature fluctuations: Ensure that the thermostat is correctly calibrated and that the heating and cooling system is functioning properly.

Conclusion

The Intronics Digital Room Thermostat is a user-friendly and feature-rich device that provides precise temperature control and energy efficiency. By following this guide, homeowners can optimize the performance of their thermostat and enjoy a comfortable indoor climate while reducing their energy bills. With its advanced features and intuitive interface, the Intronics Digital Room Thermostat is an excellent choice for homeowners seeking a reliable and efficient heating and cooling solution.

Recommendations

Based on the features and benefits of the Intronics Digital Room Thermostat, we recommend:

Installation by a qualified technician: Ensure that the thermostat is installed correctly to guarantee optimal performance.
Regular maintenance: Regularly check and maintain the thermostat to ensure that it continues to function efficiently.

Appendix

For further information on the Intronics Digital Room Thermostat, refer to the following resources:

User manual: Consult the user manual for detailed instructions on operating and troubleshooting the thermostat.
Intronics website: Visit the Intronics website for additional resources, including FAQs and technical support.

The Intronics digital room thermostat series, including the popular PI02, PI04, and DT-08 models, provides precise temperature control for various HVAC systems such as mini-split, duct-type, or chilled water systems. Core Features

P+I Control: Models like the PI02 and PI04 use Proportional + Integral control to maintain optimal comfort.

User Interface: Features a bright LED/LCD display with backlit or capacitive touch buttons.

System Modes: Typically includes 3 fan speeds, Power on/off, and specific modes like Econo, Turbo, and Sleep.

Safety Features: Built-in compressor time delay, auto-restart, and self-diagnostics. Basic Operation & Programming

Power On/Off: Press the dedicated power button. The unit will typically restart using its last saved settings. Adjusting Temperature: Use the Up ( △triangle ) or Down ( ) arrows to set your desired temperature.

Changing Modes: Use the Mode button to switch between functions or the Sweep button for air direction on supported models.

Installer Setup: To access deeper settings like minimum/maximum temperature limits: Press and hold △triangle simultaneously for 10 seconds.

The first digit on the display indicates the Program number (e.g., "1" for Min Temp, "2" for Max Temp). The second digit indicates the current Parameter setting. △triangle to cycle through program numbers and to adjust the parameters. Quick Troubleshooting Tips

Sensor Error: If the display shows a sensor error alarm, check the connection to the internal or optional remote sensor.

Compressor Protection: The "Compressor Status" indicator might flash during a built-in 3-minute delay intended to protect the system from short-cycling.

Persistent Settings: These units use EEPROM to store user settings permanently, so your preferences won't be lost during a power outage. SERIES Digital Room Thermostat II INSTALLATION MANUAL

Power On/Off: Press the main power button to toggle the unit. The display will show your last used settings upon startup.

Adjust Temperature: Use the Up and Down arrows to set your desired comfort level. On most digital displays, the larger number is the current room temperature, while the smaller number indicates your target set-point.

Select Fan Speed: Press the fan button to cycle through Low, Medium, and High speeds.

Change Mode: Use the Mode button to switch between Cool, Heat, and Auto (available on certain models like the DT-08). Advanced Features & Symbols

Turbo Function: Use this for rapid cooling when you first enter a warm room.

Econo Mode: Limits energy consumption by maintaining a slightly wider temperature range.

Frost Protection: Many Intronics models automatically turn on the heat if the room drops below a preset safety value (typically around 10°C) to prevent frozen pipes. Display Symbols: Snowflake: Cooling system is active. Flame/Sun: Heating system is active. A: Auto mode is managing both heating and cooling. Installation & Troubleshooting SERIES Digital Room Thermostat II INSTALLATION MANUAL

Table 2. Set up table. Example 1 : the display shows steady means the set up is now for Heat / Cool version. Change the set up. a) Sangchai Group Intronics digital room thermostat user guide

The Intronics Digital Room Thermostat , specifically models like the

and PI series, is designed for precise temperature control in mini-split, duct-type, or chilled water systems. These devices feature back-lit LCD displays and Proportional + Integral (P+I) control for optimal comfort. Core Operation Guide

Power On/Off: Press the power button to toggle the unit. When turned on, it typically defaults to the last saved program setting.

Temperature Adjustment: Use the △ (Up) or ▽ (Down) keys to set your desired temperature. The standard set-point range is 10°C to 35°C (50°F to 95°F).

Fan Speed Selection: Cycle through the three available fan speeds (Low, Medium, High) using the designated fan or mode button.

Mode Selection: Depending on the model, use the Mode button to switch between Cool, Heat, Dry, or Auto functions.

Energy Saving (Econo): Activate the Econo function to optimize energy usage, which often sets the temperature to a pre-defined energy-efficient level (e.g., 18°C).

Turbo Mode: Use the Turbo function for rapid cooling when the room is initially too warm. Advanced & Installer Settings

To access deeper configuration menus for system protection and calibration:

Enter Setup: Press and hold the △ and ▽ keys simultaneously for 10 seconds. A dot or specific indicator will appear on the display.

Navigate Menus: Use the △ key to advance through program numbers and the ▽ key to change parameter settings. Key Settings: Calibration: Adjust temperature display accuracy.

Frost Protection: Sets a minimum temperature (default 10°C) to prevent pipes from freezing when the unit is "Off".

Compressor Delay: Protects the compressor by preventing rapid cycling.

Exit: Press the power or escape button to save and exit the installer menu. Installation Basics

Wiring: Use 0.5-1 sq. mm cable size. Ensure the AC mains supply is kept separate from signal wiring to avoid interference.

Mounting: The backplate is separable for easier installation. Secure the backplate to the wall before snapping the front case into place.

Remote Sensor: Some models support an optional external room sensor for more accurate readings in large or wet rooms. SERIES Digital Room Thermostat II INSTALLATION MANUAL

Intronics Digital Room Thermostat User Guide

Congratulations on purchasing the Intronics Digital Room Thermostat! This user guide will help you to understand the features and operation of your new thermostat, ensuring that you get the most out of your heating and cooling system.

Table of Contents

Introduction
Thermostat Overview
Installation
Operating Instructions
Programming
Troubleshooting
Maintenance
Technical Specifications

1. Introduction

The Intronics Digital Room Thermostat is a sophisticated and user-friendly device designed to provide precise temperature control in your home or office. With its advanced features and modern design, it is an ideal solution for anyone looking to upgrade their heating and cooling system.

2. Thermostat Overview

The Intronics Digital Room Thermostat consists of the following components:

LCD display screen
Temperature sensor
Control buttons (heating/cooling, up/down, set)
Programmable timer

3. Installation

Before installing your thermostat, ensure that you have:

Read and understood the user guide
Chosen a suitable location for the thermostat (e.g., near a doorway, away from direct sunlight)
Switched off the power to your heating and cooling system

To install the thermostat:

Remove the backplate from the thermostat
Connect the wires to the corresponding terminals (see wiring diagram)
Mount the backplate to the wall
Replace the thermostat on the backplate

4. Operating Instructions

To operate the thermostat:

Press the heating/cooling button to select the desired mode
Use the up/down buttons to adjust the temperature
Press the set button to confirm your selection

5. Programming

The Intronics Digital Room Thermostat allows you to program a schedule for your heating and cooling system. To program the thermostat:

Press the set button and hold for 3 seconds
Select the desired day and time
Set the temperature for each time period
Press the set button to confirm your selections

6. Troubleshooting

If you encounter any problems with your thermostat, refer to the troubleshooting guide:

Thermostat not turning on: Check power supply and wiring connections
Temperature not accurate: Check temperature sensor and adjust calibration if necessary

7. Maintenance

To ensure optimal performance, clean the thermostat regularly:

Use a soft cloth to wipe down the exterior
Avoid using harsh chemicals or abrasive materials

8. Technical Specifications

Power supply: 24V AC
Temperature range: 10°C to 30°C
Accuracy: ±0.5°C
Dimensions: 120mm x 80mm x 30mm

We hope that this user guide has helped you to understand and operate your Intronics Digital Room Thermostat. If you have any further questions or concerns, please do not hesitate to contact us.

The Intronics digital room thermostat, particularly models like the Digital Room Thermostat II and DT-08, is designed for user-friendly operation of air conditioning and fan coil systems. Basic Operation

Most Intronics digital thermostats use a simplified interface to manage your indoor climate:

Power On/Off: Press the main power button to toggle the unit. It typically resumes the last programmed settings upon starting.

Temperature Setting: Use the UP and DOWN arrow buttons to adjust the target temperature. On models with two displays, the larger number is often the current room temperature, while the smaller one is your setpoint.

Fan Speed: Select between three speeds (High, Medium, Low) or an AUTO mode that adjusts speed based on the temperature difference.

Mode Selection: Use the MODE button to cycle through functions like Cool, Fan, and Heat (depending on your specific model). Advanced Features

Intronics models often include specialized comfort and efficiency modes: Turbo Cool: Activates rapid cooling for immediate relief. Econo Function: Optimizes performance for energy savings.

Sleep Mode: Gradually adjusts the temperature (raising it in Cool mode or lowering it in Heat mode) by 1°C after the first hour to save energy while you sleep.

Timer: Allows you to schedule the unit to turn on or off up to 15 hours in advance.

Sweep Control: On compatible units, this button toggles the oscillating fan motor. Setup & Configuration

For technicians or advanced users, the Digital Room Thermostat II has a hidden setup mode to customize system behavior:

Enter Setup: Press and hold the UP and DOWN buttons simultaneously for 3 seconds.

Navigate Parameters: Use the arrows to move through settings (e.g., P1 for Heat/Cool version, P3 for Celsius/Fahrenheit toggle).

Save/Exit: Press the MODE (or designated exit) button to save your changes. Note that pressing the POWER button before exiting may cancel your changes. Common Models & Compatibility

PI Series (PI02/PI04): Feature Proportional + Integral (P+I) control for more precise temperature maintenance.

DT-08: A two-piece unit suitable for mini-splits and chilled water systems, featuring a self-diagnostic mode and auto-restart capability.

Remote Units: Many models are compatible with Intronics wireless remote units for control from across the room. Intronics digital room thermostat user guide

8. Troubleshooting Common Intronics Problems

Even digital tech can stumble. Here is how to fix the top 5 complaints.

Problem 5: The temperature reading is wrong.

Solution: Avoid drafts. Do not install the thermostat on an exterior wall or above a radiator. Use the F1 Calibration setting (see Section 6) to manually correct a 1-2°C discrepancy.

Programming (programmable/week models)

General approach (exact steps vary by model):

Set current time and day:
- Enter CLOCK/TIME menu, set hour/minute, then day.
Set program structure:
- Choose day grouping (e.g., 5/2 or 7-day).
- Select number of switching periods per day (commonly 4 or 6).
For each period:
- Set ON time and desired temperature.
- Set OFF time and temperature for next period.
Repeat for other days/groups.
Activate program mode:
- Select AUTO or PROG mode on main screen to enable schedules.
Temporary overrides:
- Use +/– to raise/lower setpoint; temporary changes typically last until next scheduled period or until cancelled.
Holiday/Boost:
- Some models allow a holiday mode (holds a single temperature for a set number of days) or boost (temporary call for heat for fixed duration).

Refer to on-device prompts or the exact model manual for button sequences.

5. Programming a Weekly Schedule (Programmable Models)

Most Intronics digital thermostats allow separate programs for Weekdays (Mon–Fri) and Weekend (Sat–Sun) , or individual days.

4.2 Typical Program Structure

Most Intronics digital stats have 4 time periods per day (Morning, Day, Evening, Night). You can set different time and temperature for weekdays (Mon–Fri) and weekends (Sat–Sun) or each day individually.

| Period | Default Time | Default Temp | |--------|--------------|---------------| | P1 – Wake | 06:30 | 21°C (70°F) | | P2 – Leave | 08:30 | 16°C (61°F) | | P3 – Return | 17:00 | 21°C (70°F) | | P4 – Sleep | 22:00 | 17°C (63°F) | Digital Display : A clear and easy-to-read LCD